FAQs

Yes. The seals for the CYCLONE® have a coarser thread and the tolerance is set for CYCLONE® material. The seals for the VAULT® have finer threads and the tolerance is set for the VAULT® material.

During installation ensure that the penetrant is aligned and has 360 degrees of compression from the Exit Seal.  Little to zero maintenance is required due to the fact that our RPH Exit SealTM is made of SilX-14 and will not crack, separate, or deform.

Our RPH Exit SealsTM can withstand temperatures ranging from -65°F (intermittent -100°F) to +450°F (intermittent to +500°F).

NO! Doing so will comprise the integrity of the seal. The holes in the gasket are sized specifically for each individual penetrant.

No. Insulation SHOULD NOT go through the RPH Exit SealTM. The hole in the gasket is designed to fit snugly against the pipe, creating a thermal break to avoid condensation issues in the unit.

No. The RPH Exit SealsTM are specifically designed to work with the CYCLONE® and VAULT® products. The only time we will sell them separately is if they are used for a previously installed CYCLONE® or VAULT® product, and you show proof of use.

No. The lid and curb should NEVER have a penetration. Doing so will compromise the integrity of the VAULT® and void the warranty. In addition, the lid and the curb should never be punctured. Only use the pre-drilled holes for the fasteners.

The housing has a 3″ built-in counterflashing. The curb to housing connection acts as a termination for the roof material.

We add R4 insulation to provide a minimal level of protection; however a vapor barrier and additional insulation must be added to meet local requirements.

All penetrations should be supported no more than 12” from exiting the housing, and also, below the roof level as near as possible to the bottom of the roof opening. FAILURE TO DO SO WILL VOID THE WARRANTY.

20 years

3 years

The size options for manufacturing CYCLONE® products vary depending on the specific product. We offer a range of sizes that have been thoroughly tested and meet our quality standards. The sizes must be within the range of the smallest and largest tested options to ensure compliance. We can provide guidance and assistance in choosing the appropriate size for your specific requirements.

Yes

Absolutely! Both the CYCLONE® Vent Through Roof (CVTR) and CYCLONE® Roof Drain (CRD) are designed to be compatible with precast and poured-in-place applications. However, it is crucial to follow the specific instructions provided to ensure correct installation and optimal performance in these applications.

The Standard VAULT® is tested and meets the requirements of the 2023 Florida Building Code. The Standard VAULTs were tested to HVHZ and Large Missile Impact requirements in accordance with TAS 201, TAS 202, and TAS 203. The Standard VAULTs were tested to a design pressure of +/- PSF.

The Standard VAULT® was created to change the paradigm in roof penetrations by providing a single, secure pathway for multiple penetrations through the roof which eliminates leaks and meets the building code requirements for air permeance and missile impact (e.g., ICC, Miami-Dade/Florida).

 

The Standard VAULT® was created as a superior alternate solution to pitch pans. As seen time and again in the industry, the pitch pans will fail because the sealant can dry out and shrink, causing leaks. Putting a rubber boot or diverter on it doesn’t solve the problem in the long term, and can even create additional issues. The VAULT®, however, provides a single pathway for multiple penetrations and will replace vertical penetrations with a tightly sealed horizontal penetration.

All penetrations should be supported no more than 12” from exiting the housing, and also, below the roof level as near as possible to the bottom of the roof opening. FAILURE TO DO SO WILL VOID THE WARRANTY.

We add R4 insulation to provide a minimal level of protection; however a vapor barrier and additional insulation must be added to meet local requirements.

The housing has a 3″ built-in counterflashing. The curb to housing connection acts as a termination for the roof material.

No. The lid and curb should NEVER have a penetration. Doing so will compromise the integrity of the VAULT® and void the warranty. In addition, the lid and the curb should never be punctured. Only use the pre-drilled holes for the fasteners.

20 years

No. The RPH Exit SealsTM are specifically designed to work with the CYCLONE® and VAULT® products. The only time we will sell them separately is if they are used for a previously installed CYCLONE® or VAULT® product, and you show proof of use.

It is imperative that no sealants are applied to our units. Our VAULT® and CYCLONE® products, when used in combination with our RPH Exit SealsTM, form an ENGINEERED SYSTEM that guarantees the end user uninterrupted service for many years. This is precisely why we confidently provide a 20-year warranty to our customers.

No. Insulation SHOULD NOT go through the RPH Exit SealTM. The hole in the gasket is designed to fit snugly against the pipe, creating a thermal break to avoid condensation issues in the unit.

NO! Doing so will comprise the integrity of the seal. The holes in the gasket are sized specifically for each individual penetrant.

Our RPH Exit SealsTM can withstand temperatures ranging from -65°F (intermittent -100°F) to +450°F (intermittent to +500°F).

During installation ensure that the penetrant is aligned and has 360 degrees of compression from the Exit Seal.  Little to zero maintenance is required due to the fact that our RPH Exit SealTM is made of SilX-14 and will not crack, separate, or deform.

Yes.

Yes. The seals for the CYCLONE® have a coarser thread and the tolerance is set for CYCLONE® material. The seals for the VAULT® have finer threads and the tolerance is set for the VAULT® material.

Expand Your Knowledge and Explore Upcoming Education Opportunities

Whether you’re interested in one of our upcoming webinars or you are interested in a private session with our experts, our team is ready to assist you in expanding your knowledge as it applies to protecting the building envelope.

Which Solution Is Right for Me?

Let Us Help You Find the Right Solution for Your Needs